If there are images in this attachment, they will not be displayed.  Download the original attachment
Page 1
OWNER’S MANUAL /
Instructions for Assembly
• Tall Walk in Shed
• Quick & Easy Assembly
• Ridge Reinforced Walls
• Wide Double Doors
• Available in Various Sizes
Call us for any missing or damaged parts.
Do not return to the store.
Poly Storage Shed
Customer
Service Hotline
(800) 483-4674
www.uspolymersinc.com
Requires two people and takes 2-3 hours for Installation.
Ver: 1.0
A L L
P U R P O S E
P O L Y
S T O R A G E
S H E D S
Size 10’ x 6’

Page 2
Duramax Storage Shed
Limited Ten Year Warranty
U.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or
workmanship for a period of ten years from the date of purchase.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of date of original
purchase will be required before warranty service is rendered. In no event shall we pay the cost of flooring,
labor, installation or any other costs related thereto.
This warranty only covers failures due to defects in material or workmanship which occurs during normal
use and does not extend to color change arising due to normal weathering or to damage resulting from
misuse or neglect, commercial use, failure to follow assembly instructions and the owner’s manual (including
proper anchoring of the shed), painting, forces of nature and other causes which is beyond our control.
Claims under this warranty must be made within the warranty period by calling 1-800-483-4674 or mail in
a dated sales slip and clear photograph of the part to:
U.S. Polymers, Inc.
6915 Slauson Avenue
Commerce, CA 90040
We reserve the right to discontinue or change components. If a component has been discontinued or is
not available,
U.S. Polymers, Inc. reserves the right to substitute a component of equal quality as may be compatible.
Limits and Exclusions
There are no express warranties except as listed above. The warrantor shall not be liable for incidental or
consequential damages resulting from the use of this product, or arising out of any breach of this warranty.
All express warranties are limited to the warranty period set forth above . Some states do not allow the
exclusion or limitation on how long an implied warranty lasts, so the above limitations may not apply to
you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to
state or country to country.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.

Page 3
ACCESSORIES
CODE
DESCRIPTION
QTY
FCFP
FRONT COLUMN FITTING
2
CCFP
CORNER COLUMN FITTNG
4
CFP
COLUMN FITTING
16
DCBFP DOOR COLUMN BOTTOM FITTING
2
CBFP
CENTER BAND FITTING
8
BS
BOTTOM SLIDER
4
DH
DOOR HANDLE
2
FC
RIDGE END CAP
2
TC
TOP CORNERS
4
TS
TOP SLIDER
4
PPG
ROOF PLUG WITH WASHER
48
PIN
ROOF PIN
48
PW
PLASTIC WASHERS
288
PC
PLASTIC SCREW COVER
109
S1
SHEET METAL SCREW
420
DIA. 4.2mm.x16.0mm. (5/32”x5/8”)
S3
MACHINE SCREW with NUTS
66
M4x10.0mm. (5/32”x3/8”)
S7
SHEET METAL SCREW
62
DIA. 4.2mm.x10.0mm. (5/32”x3/8”)
Note: Check all parts prior to installation.
CODE
DESCRIPTION
QTY
BLAP
BASE BAR BACK LEFT
1
BRAP
BASE BAR BACK RIGHT
1
BSBP
BASE BAR SIDE
2
BBFP
BASE BAR FRONT
2
ECAP
ENTRANCE TAPER CHANNEL
1
COLP
COLUMN LONG
14
COSP
COLUMN SHORT
2
DCLP
DOOR COLUMN PROFILE LEFT
1
DCRP
DOOR COLUMN PROFILE RIGHT
1
CS
COLUMN SUPPORT
4
CB1P
CENTER BAND FRONT
2
CB2P
CENTER BAND SIDE FRONT
2
CB3P
CENTER BAND SIDE FRONT
2
CB4P
CENTER BAND MIDDLE
7
SLAP
SLIDING CHANNEL LEFT
1
SRAP
SLIDING CHANNEL RIGHT
1
SJP
SLIDING CHANNEL JOINT
1
SCAP
SLIDING CHANNEL COVER LEFT/RIGHT
2
ASBP
TOP ANGLE SIDE LEFT/RIGHT
2
ABLAP TOP ANGLE BACK LEFT
1
ABRAP TOP ANGLE BACK RIGHT
1
SB1AP SUPPORT BRACKET
FRONT RIGHT/BACK LEFT
2
SB2AP SUPPORT BRACKET
FRONT LEFT/BACK RIGHT
2
SB3AP SUPPORT BRACKET LONG
FRONT RIGHT/BACK LEFT
2
SB4AP SUPPORT BRACKET LONG
FRONT LEFT/BACK RIGHT
2
FBS
FACIA BRACKET SUPPORT
8
FSLAP FACIA SUPPORT LEFT
2
FSRAP FACIA SUPPORT RIGHT
2
RSBP
ROOF SUPPORT
4
RS4AP ROOF STRUCTURE
4
RF1AP ROOF FLASHING
FRONT RIGHT/BACK LEFT
2
RF2AP ROOF FLASHING
FRONT LEFT/BACK RIGHT
2
RF3BP ROOF FLASHING
FRONT LEFT/BACK RIGHT
2
RF4BP ROOF FLASHING
FRONT RIGHT/BACK LEFT
2
DSTAP DOOR PANEL STRIP TOP
2
DSBAP DOOR PANEL STRIP BOTTOM
2
DMSAP DOOR PANEL MIDDLE SUPPORT
2
DVSP
DOOR PANEL VERTICAL SUPPORT
2
DSP
DOOR STOPPER VERTICAL
2
WP1A
FRONT WALL PANEL LEFT
1
WP2A
FRONT WALL PANEL RIGHT
1
WP3A
CORNER WALL PANEL
4
WP4A
WALL PANEL
7
FLAP
FACIA PANEL LEFT
2
FRAP
FACIA PANEL RIGHT
2
RP1AP ROOF PANEL
2
RP2AP ROOF PANEL
2
RP4AP ROOF PANEL
2
RC1P
RIDGE COVER
1
RC2P
RIDGE COVER
2
DL1AP DOOR PANEL LEFT
1
DL2AP DOOR PANEL LEFT
1
DR1AP DOOR PANEL RIGHT
1
DR2AP DOOR PANEL RIGHT
1
Parts List
BASE BAR
(BLAP, BRAP, BSBP)
PROFILES
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
TOP ANGLE BACK
(ABLAP, ABRAP)
BASE BAR FRONT
(BBFP)
DOOR COLUMN
PROFILE LEFT
(DCLP)
ENTRANCE TAPER CHANNEL
(ECAP)
DOOR COLUMN
PROFILE RIGHT
(DCRP)
SLIDING CHANNEL COVER
(SCAP)
TOP ANGLE SIDE
(ASBP)
SLIDING CHANNEL
(SLAP, SRAP)
SLIDING CHANNEL
SUPPORT
(SJP)
ROOF SUPPORT
BRACKET
(SB1AP, SB2AP)
ROOF FLASHING
(RF1AP, RF2AP,
RF3BP, RF4BP
ROOF SUPPORT
(RSBP)
DOOR PANEL VERTICAL
SUPPORT
(DVSP)
DOOR STOPPER
VERTICAL
(DSP)
DOOR PANEL MIDDLE
SUPPORT
(DMSAP)
COLUMN
(COLP, COSP)
CENTER BAND
(CB2P, CB3P, CB4P)
CENTER BAND FRONT
(CB1P)
PLASTIC WASHER
(PW)
TOP SLIDER
(TS)
TOP CORNERS
(TC)
DOOR HANDLE
(DH)
BOTTOM SLIDER
(BS)
CENTER BAND FITTING
(CBFP)
CORNER COLUMN FITTING
(CCFP)
COLUMN FITTING
(CFP)
ROOF PLUG
(PPG)
ROOF PIN
(PIN)
RIDGE END CAP
(FC)
MACHINE SCREW WITH
NUT (S3)
SHEET METAL SCREW
(S1, S7)
FACIA SUPPORT
(FSLAP, FSRAP,
SB3AP, SB4AP)
DOOR PANEL STRIP
(DSTAP, DSBAP)
ROOF SUPPORT
(RS4AP)
PLASTIC SCREW COVER
(PC)
COLUMN SUPPORT
(CS)
FACIA BRACKET
SUPPORT (FBS)
FRONT COLUMN FITTING
(FCFP)
DOOR COLUMN
BOTTOM FITTING
(DCBFP)

Page 4
Exploded View
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
RC2P
RC2P
RC1P
RF3BP
RF4BP
RF2AP
RF1AP
RF2AP
RF1AP
RF3BP
RF4BP
RS4AP
FLAP
FRAP
RSBP
FSRAP
FRAP
FLAP
FSLAP
SB1AP
SB4AP
SB2AP
SB1AP
FBS
SB4AP
RSBP
RS4AP
SB2AP
ASBP
ABLAP
ASBP
SLAP
SRAP
SJP
CB3P
CB4P
CB2P
COLP
WP3A
WP4A
CB4P
WP3A
WP4A
BRAP
BLAP
BSBP
BBFP
ECAP
COSP
WP2A
DCLP
SCAP
SCAP
DCRP
CB1P
WP1A
SB3AP
FSLAP
FSRAP
ABRAP
COLP
COLP
CB1P
BSBP
WP4A
COSP
BBFP
RP4AP
RP2AP
RP1AP
RP2AP
RP1AP
RP4AP
CB3P
CB2P
CB4P
SB3AP

Page 5
A. Foundation & Base Frame
1
. Use pressure treated wood studs 2”x 4”
(50mm x 101.6mm) to create a platform frame that
has an outside dimension of 126” x 71”
(3200.4mm x 1803mm).
DuraMax must be installed on a level wooden platform
or a level concrete foundation.
2
. Using exterior grade CDX 3/4” (19mm) plywood,
cut and fit together the sheets to form solid foundation
as shown. Foundation must be square and level.
Note: It is important that these instructions
are followed step by step.
Wooden platform is extra and
is not included. Don’t install
under windy conditions.
1
Note
Lay 50mm x 88.9mm Flat
Note
96” (2438.4mm)
30”
(762mm)
(1) Base bar back left
(BLAP)
(1) Base bar back right
(BRAP)
(2) Base bar side left & right
(BSBP)
(2) Base bar front
(BBFP)
(1) Entrance taper channel
(ECAP)
(8) Sheet metal screws
(S7)
(24) Sheet metal screws
(S1)
Parts needed:
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
The following are a list of lumber and sizes
you will need.
Wooden Platform (Not Included)
Pressure Treated - Wood Studs:
2ea 2” x 4” x 90 3/4” (50mm x 101.6mm x 2305mm)
2ea 2” x 4” x 126” (50mm x 101.6mm x 3200.4mm)
3ea 2” x 4” x 64” (50mm x 101.6mm x 1625.6mm)
Exterior Grade (CDX) - 3/4” (19mm) plywood
1ea 3/4” x 23” x 96” (19mm x 584.2mm x 2438.4mm)
1ea 3/4” x 48” x 96” (19mm x 1219.2mm x 2438.4mm)
1ea 3/4” x 30” x 71” (19mm x 762mm x 1803.4mm)
L-Brackets: 4ea
L- BRACKET
L- BRACKET
L- BRACKET
L- BRACKET
23” (584.2mm)
48” (1219.2mm)
71” (1803.4mm)
17 3/4” (452mm)
19 5/8” (498mm)
19 5/8 (498mm)
90 3/4” (2305mm)
126” (3200.4mm)
24 3/4”
(628mm)
64” (1625.6mm)

Page 6
3
. Assemble base bar back left (BLAP) and base
bar back right (BRAP) with four (S7) screws.
See fig. 1 & 2.
4
. Place the base bar assembly on top of the
foundation. Use (S1) screws to fix the assembly to
foundation.
2
5
. Insert the base bar side (BSBP) into (BLAP) &
(BRAP). Secure with two (S7) screws on both sides.
See blowup.
Fig.1
Fig.2
BLAP
S7
BLAP
BRAP
BLAP
BRAP
Front
Right
Left
Back
Fig.1
Fig.2
Step 1
Step 2
BLAP
BRAP
BSBP
BSBP
BSBP
BLAP
BRAP
BSBP
S7
Take care of sharp edges.
Note
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
BRAP
S7
1
2

Page 7
3
6
. Using a carpenter square, line up the corners.
Secure the base (BSBP) to the foundation with (S1)
screws. See blowup.
7
. Place the base bar (BBFP) on top of (BSBP)
on both sides. Secure with (S7) screw to (BSBP)
on both corners. See fig. 1 & 2.
8
. Using the carpenter square, line up the corners.
Secure the base (BBFP) to the foundation with (S1)
screws.
BSBP
BBFP
BBFP
BBFP
BSBP
BBFP
BSBP
Fig.1
Fig.2
BBFP
BBFP
S1
BSBP
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
S7
BSBP
BSBP

Page 8
4
9
. Place the entrance taper channel (ECAP) on top
of the (BBFP). Secure with (S1) screws to the
foundation. See fig. 1 & 2.
10
. Measure in all direction as shown in figure.
Make the base bar assembly in a perfect square.
BBFP
BBFP
S1
Fig.1
Fig.2
ECAP
ECAP
BBFP
BBFP
Parts Needed:
(2) Column short
(COSP)
(14) Column long
(COLP)
(4) Column support
(CS)
(1) Wall panel front left
(WP1A)
(1) Wall panel front right
(WP2A)
(4) Wall panel corner
(WP3A)
(7) Wall panel side
(WP4A)
(1) Sliding channel right
(SRAP)
(1) Sliding channel left
(SLAP)
(1) Sliding channel joint
(SJP)
(2) Sliding channel cover left / right (SCAP)
(2) Top angle side left & right
(ASBP)
(1) Top angle back left
(ABLAP)
(1) Top angle back right
(ABRAP)
(2) Center band front
(CB1P)
B. Walls & Columns
All panels are clearly marked
and care should be taken to
use the correct one.
Note
10a
. (Concrete foundation) Using a carpenter’s
square, line up corners. Align Base bars, mark the
concrete at the holes in the base and drill concrete
with 1/4” (dia. 6mm) concrete bit to accept anchor
bolts to a 1 3/4” (44mm) depth. Replace base and
secure with 1/4” x 1 3/8” (M6 x 35mm) anchor bolts
(not provided).
Concrete foundation
BBFP
ECAP
BSBP
BSBP
BRAP
BLAP
(3037mm
)
(1569
mm)
(2) Center band side front (CB2P)
(2) Center band side back (CB3P)
(7) Center band middle (CB4P)
(1) Door column profile left(DCLP)
(1) Door column profile right(DCRP)
(4) Corner column fitting (CCFP)
(8) Center band fitting
(CBFP)
(2) Front column fitting
(FCFP)
(16) Column fitting
(CFP)
(4) Top slider
(TS)
(156) Plastic washer
(PW)
(260) Sheet metal screw
(S1)
(16) Sheet metal screw
(S7)
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
(1569
mm)
(3037mm
)

Page 9
5
1
. Place the corner column fitting (CCFP) on top of
the base bar (BBFP & BSBP). Secure with the three
(S1) screws to the base bar.
Follow the same at the other corner.
2
. Insert the column (COSP) & (COLP) in to corner
column fitting and secure with (S1) screws from
inside. Insert the column (COSP) at the top of base
(BBFP) and column (COLP) at the top of (BSBP)
3
. Fix the column support (CS) to the column with
two (S1) screws.
Make sure the direction of the
column opening and arrow up
as per blow up.
Note
Fig.1
Fig.2
CCFP
BBFP
COSP
S1
COLP
S1
BSBP
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
BACK
BBFP
BSBP
CCFP
S1
S1
BBFP
cs
BSBP
BSBP
BBFP
BBFP
BBFP

Page 10
6
4
. Insert the column (COSP) & (COLP) in to corner
column fitting and secure with (S1) screws from
inside. Insert the column (COSP) at the top of base
(BBFP) and column (COLP) at the top of (BSBP)
5
. Fix the column support (CS) to the column with
two (S1) screws.
6
. Assemble the sliding channel (SLAP & SRAP)
together with sliding channel joint (SJP). Secure
with 8 screws (S7)
Fig.1
Fig.2
BSBP
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
S1
COLP
COSP
Fig.3
BBFP
cs
S1
SLAP
SJP
SRAP
SJP
S7
SRAP
SLAP
Make sure the direction of the
column opening and arrow up
as per blow up.
Note

Page 11
7
7
. Insert the front column fitting at the top of front column
(COSP) and secure with (S1) screws from inside.
Continue the same at the other side.
8
. Place the sliding channel assembly (SLAP & SRAP)
on the top of front column fitting at the both ends.
Secure with (S1) screws.
9
. Insert 4 nos of top slider (TS) into the sliding channel
as per the direction shown.
Fig.1
Fig.2
COSP
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
FCFP
SLAP
SRAP
FCFP
S1
SRAP
TS
FCFP
S1
COSP
2
1

Page 12
8
10
. Place the wall panel (WP3A) on the base bar
(BSBP) front right side of the shed. Line up the holes
with base bar.
Secure with (S1) screws with washers from out side.
11
. Place the wall panel (WP2A) on the base bar
(BBFP). Line up the holes with base bar.
Secure with (S1) Screws.
Fig.1
Fig.2
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
WP3A
BSBP
S1
WP2A
WP2A
BBFP
S1
S1
SRAP
WP3A
2
1
WP2A
FRONT
BBFP
First fix the middle screws then
go to the edges.
Tip
First fix the middle screws (top
or bottom) then go to the edges.
Tip
S1
ECAP
BBFP
DCBFP
WP2A
12
. Fix to door column bottom fitting (DCBFP) on
the base bar (BBFP) with (S1) screws.

Page 13
13
. Place the right Door column (DCRP) on top of
the base bar (BBFP) and insert into the wall panel
(WP2A). Line up the holes with wall panel and secure
with (S1) screws.
S1
BBFP
DCRP
Fig.2
DCRP
Fig.3
3
1
2
WP2A
S1
SRAP
SRAP
DCRP
WP2A
Fig.1
9
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
14
. Fix the door column bottom to the fitting (DCBFP)
with (S1) screws.
WP2A
BBFP
15
. Assemble the center band (CB1P) with column
fitting (CFP). Secure with (S1) screw at one end.
Make 2 Sets.
Fig.1
Fig.2
CB1P
CFP
S1
CB1P
DCRP
BBFP
S1
Note
Make sure the door column
bottom fitting to be inside
the door column.

Page 14
10
16
. Fix the column fitting (CFP) to the front column
(COSP) with (S1) screws from inside, fix the other
end to the Door Column (DCRP) through the wall
panel with (S1) screw from inside.
17
. Secure the wall panel (WP2A) to the center
band (CB1P) with (S7) screws from outside.
Fig.1
Fig.2
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
DCRP
S1
CB1P
CB1P
S1
COSP
2
1
S7
WP2A
18
. Place the wall panel (WP3A) on the base bar
(BSBP) front left side. Line up the holes with base bar.
Secure with (S1) screws with washers from out side.
Fig.1
WP3A
BSBP
S1
FRONT
First fix the middle screws then
go to the edges.
Tip

Page 15
11
Make sure the overlapping
position of panels is as
shown in fig. 2.
Note
19
. Place the wall panel (WP1A) on the base bar
(BBFP). Line up the holes with base bar.
Secure with (S1) screws.
21
. Place the left Door Column (DCLP) on top of
the base bar (BBFP) and insert in to the wall panel
(WP1A). Line up the holes with wall panel and secure
with (S1) screws.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
WP1A
BBFP
WP3A
WP1A
Fig.1
Fig.2
S1
Fig.1
Fig.3
WP1A
Fig.2
S1
S1
DCLP
3
2
1
DCLP
WP1A
SLAP
BBFP
WP1A
SLAP
DCLP
BBFP
First fix the middle screws (top
or bottom) then go to the edges.
Tip
20
. Fix to door column bottom fitting (DCBFP) on
the base bar (BBFP) with (S1) screws.
S1
BBFP
ECAP
DCBFP
WP1A
Note
Make sure the door column
bottom fitting to be inside
the door column.

Page 16
12
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Fig.1
Fig.2
23
. Fix the Column fitting (CFP) to the front Column
(COSP) with (S1) screw from inside.
Fix other end to the Door Column (DCLP) through the
wall panel with (S1) screw from inside.
S1
DCLP
CB1P
S1
CFP
2
1
WP1A
24
. Secure the wall panel (WP1A)to the centre band
(CB1P) with (S7) screws from outside.
22
. Fix the door column bottom to the fitting
(DCBFP) with (S1) Screws.
S1
DCLP

Page 17
13
25
. Place the Corner Column fitting (CCFP) on top
of the base bar at the back side on both corners.
Secure with (S1) screws.
26
.Insert the column (COLP) into the Corner Column
fitting (CCFP) and secure with (S1) screws.
Fig.1
Fig.2
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
Make sure the direction of
the Column opening and
arrow up as per blowup
Note
CCFP
S1
COLP
COLP
S1
CCFP
S1
1
2
Fig.1
Fig.2
Fig.3
Fig.4
COLP
COLP
Fig.5
1
2 & 3
4
5
BACK
COLP
COLP

Page 18
Fig.1
14
27
. Fix the Column Support (CS) to the columns with
two (S7) screws at both corners.
28
Place the wall panel (WP3A) on the base bar
side (BSBP) at back left .
Line up the hole with base bar and secure with (S1)
screws with washers from out side.
29
. Place the wall panel (WP4A) on the base bar
back left (BLAP).
Line up the holes with base bar and secure with (S1)
screws. See the blow up
Fig.1
Fig.2
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S7
COLP
COLP
CS
S1
BSBP
S1
WP4A
WP3A
FRONT
BACK
WP3A
WP4A
1
2
BSBP
BLAP
Make sure the overlapping
position of panels is as
shown in fig. 2.
Note
First fix the middle screws then
go to the edges.
Tip
First fix the middle screws than
go to the edges.
Tip

Page 19
15
30
. Place the wall panel (WP3A) on the base bar
(BSBP). Line up the holes with base bar and secure
with (S1) screws with washer from out side.
31
. Place the wall panel (WP4A) on the base bar
(BRAP). Line up the hole with base bar and secure
with (S1) screw with washer from out side.
32
. Assemble the top back angle left & right (ABLAP
& ABRAP) together with (S7) screws.
See the blow up
Fig.1
Fig.1
Fig.2
DCL
BBF
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
WP3A
S1
S1
BRAP
WP4A
BRAP
WP4A
ABRAP
ABLAP
S7
ABLAP
ABRAP
BSBP
WP3A
BSBP
Make sure the overlapping
position of panels is as
shown in fig. 2.
Note
First fix the middle screws then
go to the edges.
Tip
First fix the middle screws (top
or bottom) then go to the edges.
Tip

Page 20
16
33
. Place the assembled top angle back in between
the column and back wall panel top side. Line up the
holes with panel and secure with (S1) screws from
outside.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
ABRAP
S1
ABLAP
S1
34
. Place the top angle side (ASBP) on top of back
top angle (ABLAP) and top of sliding channel (SLAP).
Secure with (S1) screws from top.
Fig.1
Fig.2
1
2
ASBP
ASBP
S1
S1
Fig.1
Fig.2
35
. Secure the wall panel to the top angle with (S1)
screws.
S1
2
1
ABLAP
ABRAP
ASBP

Page 21
S1
17
37
. Secure the Wall Panel to the top angle with (S1)
screws.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
36
. Place the top angle side (ASBP) on top of sliding
channel (SRAP) and back top angle (ABRAP) secure
with (S1) screws.
See Details.
Fig.1
Fig.2
38
. Assemble the Column fitting (CFP)with all columns
(COLP) with (S1) screw.
Fig.1
Fig.2
ASBP
2
Fig.1
Fig.2
Make sure the direction of
arrow (Fig. 1) and opening of
the Column (Fig. 2) as Shown
Note
COLP
CFP
S1
SRAP
ASBP
ABRAP
1
1
2
1
2
S1
S1

Page 22
18
39
. Fix two column fitting with columns to the base
bar (BSBP) with (S1) screws from inside.
Fig.1
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
40
. Place the Wall Panel (WP4A) on the base bar side
(BSBP). Line up the holes with base bar and top angle.
F
ront
Back
S1
CFP
BSBP
Fig.1
Fig.2
F
ront
Back
1. Secure the Panel at bottom with (S1) screws
to the base bar from out side.
2. Secure the Panel at top with (S1) screw
through the top angle to the Column (COLP)
41
. Fix the Center band fitting (CBFP) to the Column
with (S1) screw.
Fig.1 & 2
S1
CBFP
2
1
1
2
WP4A
S1
S1
First fix the middle screws (top
or bottom) then go to the edges.
Tip

Page 23
19
42
. Fix the Column fitting (CFP) to the Column with
(S1) screw as shown.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
44
. Fix the Center band (CB4P) to the Center band
fitting with (S1) screws.
See fig. 1 & 2.
F
ront
Back
S1
CFP
43
. Fix the Center band (CB2P) to the Column fitting
(CFP) with (S1) screw. See the Fig 1.
Fix the other end of the Center band to the Center band
fitting (CBFP) with (S1) screw. See the fig. 2
CFP
CB2P
S1
Fig.1
Fig.2
CB2P
CBFP
S1
F
ront
Back
F
ront
Back
1
2
CBFP
CB4P
S1
Fig.1
Fig.2
CBFP
CB4P
S1
1
2

Page 24
Fig.1
Fig.2
20
46
. Fix the Center band (CB3P) to the Center band
fitting (CBFP) with (S1) screw. See fig.1
Fix the other end to the Column fitting (CFP).
47
. Secure the Panels to the Center bands with (S1)
screws with washer from out side.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
45
. Fix the Column fitting (CFP) to the Column with
(S1) screw as shown.
S1
CFP
F
ront
Back
F
ront
Back
CBFP
CB3P
S1
CFP
CB3P
S1
1
2

Page 25
21
48
. Fix two Column fittings (CBF) with Columns to the
other side of base bar (BSBP) with (S1) screws from
inside.
49
. Place the Wall Panel (WP4A) on the base bar
side (BSBP) Line up the holes with base bar and
top angle.
1. Secure the Panel at bottom with (S1)
screws to the base bar from out side.
2. Secure the Panel at top with (S1) Screw
through the top angle to the Column (COLP).
50
. Fix the Center band fitting (CBFP) to the Column
with (S1) screws. See Fig. 1 & 2.
Fix the Column fitting (CFP) to the Column with (S1)
screw. See Fig. 3
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
S1
CBF
S1
WP4A
2
3
Fig.1
Fig.1&2
Fig.3
S1
CFP
S1
CBFP
1
BSBP
BSBP
WP4A
1
2
S1
COLP
Fig.2
BSBP
First fix the middle screws (top
or bottom) then go to the edges.
Tip

Page 26
22
51
. Fix the Center Band (CB3P) to the Column fitting
with (S1) Screws. See Fig. 1
Fix the other end to the center band fitting (CBFP) with
(S1) screw. See Fig. 2
52
. Fix the Center Band (CB4P) to the Center Band
fitting with (S1) screws. See Fig. 1 & 2.
53
. Fix the Column fitting (CFP) to the Column with
(S1) screws as shown in blow up.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
1
2
Fig.1
1
2
CB4P
Fig.2
Fig.1
Fig.2
S1
CFP
F
ront
Back
CB3P
CBFP
S1
S1
CB4P
S1
CFP
CB3P
S1

Page 27
23
54
. Fix the Center Band (CB2P) to the Center Band
fitting (CBFP) with (S1) screw . See fig. 1
Fix to other end to the Column fitting (CFP) See fig. 2
55
. Secure Panel to the Center Bands with (S1)
screws with washer from out side.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
56
. Fix the Column fitting with Column to the back
base bar with (S1) screws from inside.
1
2
Fig.2
CB2P
S1
CBFP
S1
CFP
CB2P
S1
Fig.1
CFP

Page 28
24
58
. Fix the Column fitting with Column to the back
base bar with (S1) screws.
Fig.1
Fig.2
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
57
. Place the Wall Panel (WP4A) on the back base
bar. Line up the holes with base bar.
1
2
S1
Fig.2
Fig.1
1. Secure the Panel at bottom with (S1) screws
to the base bar from out side.
2. Secure the Panel at top with (S1) screws
through the top angle to the Column (COLP)
CFP
59
. Place the Wall Panel (WP4A) on the base bar
back. Line up the holes with base bar and top angle.
1. Secure the Panel at bottom with (S1)
screws to the base bar from out side.
2. Secure the Panel at top with (S1) Screw
through the top angle to the Column (COLP)
S1
S1
S1
S1
COLP
1
2
WP4A
WP4A
First fix the middle screws (top
or bottom) then go to the edges.
Tip
First fix the middle screws (top
or bottom) then go to the edges.
Tip

Page 29
25
60
. Fix two Column fittings (CBF) with Columns to the
back base bar with (S1) screws from inside.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
62
. Fix the Center band fitting (CBFP) on the Columns
with (S1) screw.
61
. Place the Wall Panel (WP4A) on the base bar
back. Line up the holes with base bar and top angle.
1. Secure the Panel at bottom with (S1)
screws to the base bar from out side.
2. Secure the Panel at top with (S1) Screw
through the top angle to the Column (COLP)
Fig.1
Fig.2
CBFP
S1
1
2
S1
S1
S1
S1
WP4A
First fix the middle screws (top
or bottom) then go to the edges.
Tip

Page 30
26
63
. Fix the Column fittings (CFP) to the Column as
shown.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
65
. Secure the Panels to the Center bands with (S1)
screws with washer from out side.
64
. Fix the Center Band (CB4P) with (S1) screws
to the Center Band fitting and column fitting.
1
2
CFP
Fig.1
Fig.2
S1
S1
CFP
CB4P
CB4P
CBFP

Page 31
27
66
. Place the sliding channel cover (SCAP) on sliding
channel and secure with (S7) screws at both ends.
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
67
. Place the another half of sliding channel cover
(SCAP) on sliding channel and secure with (S7)
screws at both ends.
1
SCAP
Fig.1
S7
2

Page 32
28
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
C. Roof
Parts Needed:
(2) Support bracket front right / back left
(SB1AP)
(2) Support bracket front left / back right
(SB2AP)
(2) Support bracketlong - front right / back left (SB3AP)
(2) Support bracket long - front left / back right (SB4AP)
(8) Facia bracket support
(FBS)
(2) Facia support left
(FSLAP)
(2) Facia support right
(FSRAP)
(4) Roof support
(RSBP)
(4) Roof structure
(RS4AP)
(2) Roof panel
(RP1AP)
(2) Roof panel
(RP2AP)
(2) Roof panel
(RP4AP)
(1) Ridge cover
(RC1P)
(2) Ridge cover
(RC2P)
(2) Roof flashing
(RF1AP)
All parts are clearly marked
and care should be taken to
use the correct one.
Note
(2) Roof flashing
(RF2AP)
(2) Roof flashing
(RF3BP)
(2) Roof flashing
(RF4BP)
(2) Facia panel left
(FLAP)
(2) Facia panel right
(FRAP)
(4) Top corner
(TC)
(2) Ridge end cap
(FC)
(106) Plastic washer
(PW)
(48) Roof plug with washer
(PPG)
(48) Roof pin
(PIN)
(132) Sheet metal screw
(S1)
(48) Machine screw with nut
(S3)
1
. Assemble the support bracket (SB1AP & SB2AP)
with Facia bracket support. Use (S3) bolt & nut.
Make 2 Sets
2
. Assemble the support bracket with Roof support
(RSBP) at both ends as shown. Use (S3) bolt & nut.
Make 2 Sets
S3
Fig.1
SB1AP
SB2AP
Fig. 2
SB2AP
SB1AP
S3
FBS
FBS
S3
RSBP
S3

Page 33
29
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
3
. Place the Roof support assembly on top of sliding
channel and back top angle. Use (S1)screws to secure.
Make 2 Sets.
1
3
4
4
. Assemble the Support bracket (SB3AP & SB4AP)
together with Facia bracket support (FBS). Use (S3)
bolt & nut.
Make 2 Sets
SB3AP
SB4AP
S3
FBS
5
. Assemble the Support bracket with Roof support
(RSBP) as shown. Use (S3) bolt & nut.
2
S1
Fig.1
Fig.2
S1
Fig.4
Fig.3
S1
S1
FBS
S3
Fig.1
S3
RSBP
RSBP
Fig.2
Fig.3
S3
1
2
3

Page 34
30
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
6
. Place the Roof support assembly on top of the sliding
channel and back top angle. Use (S1) screw to secure.
1
2
Fig.1
Fig.2
7
. Place the Facia support right (FSRAP) on top of
Roof support as shown. Secure with (S1) screws to
support bracket and top angle side.
1
2
8
. Place the Facia support left (FSLAP) on the top of
Roof support as shown. Secure with (S1) screw to
Support bracket and top angle side.
3
FSLAP
S1
FSRAP
Fig.3
S1
Fig.1
Fig.2
S1
FSRAP
S1
SB2AP
S1
Fig.1
FSLAP
FSLAP
ASBP
S1
Fig.3
FSLAP
S1
SB1AP
Fig.2
3
2
1

Page 35
31
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
9
. Place the Facia support left (FSLAP & FSRAP) on
the top of Roof support as shown. Secure with (S1)
screws to Support bracket and top angle side.
FSLAP
S1
1
2
3
4
5
FSLAP
FSLAP
ASBP
FSRAP
FSRAP
FSRAP
ASBP
Fig.1
Fig.2
Fig.3
Fig.4
Fig.5
10
. Place the Roof Structure (RS4AP) on the top of
Roof support and top angle side. Secure with (S1)
screws to the top angle and Roof support as shown in
Fig. 1,2,3 & 4.
Fig.1
Fig.2
Fig.3
Fig.4
RS4AP
RS4AP
S1
11
. Place the Facia panel (FRAP) on Facia support
at right side. Line up the holes with Facia support and
fix the Roof plug with washer use a hammer (rubber
mallet) to drive in roof pin.
FRAP
S1
S1
S1
S1
RS4AP
S1
S1
RS4AP
RS4AP
1
3
2
3
4
PPG
TIP
First insert all roof plugs with washers
(Left & Right) then drive in the roof pins.
PIN

Page 36
12
. Place the Facia panel (FLAP) at left side and
continue the same.
32
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
13
. Place the Facia panel (FLAP) on back side left
facia support and fix the Roof plugs with washer and
drive in roof pins.
14
. Place the Facia panel (FRAP) on back side right
Facia support and fix the roof plugs with washer and
drive in roof pins.
FLAP
FLAP
FRAP

Page 37
33
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
15
. Place the Roof panel (RP4AP) on top of the Roof
support and Facia support. Line up the holes and secure
with (S1) screws with washer.
RP2AP
RP4AP
16
. Place the Roof panel (RP2AP) on the Roof support.
Secure with (S1) screws with washer.
S1
RP4AP
17
. Place the Roof panel (RP1AP) on top of the Roof
support and Facia support. Line up the holes and secure
with (S1) screws with washer.
RP1AP
RP2AP
Note
Make sure the overlapping
position for roof panel is as
shown in blow up
RP4AP
RP2AP
RP1AP

Page 38
34
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
18
. Place the Roof panel (RP4AP) on the Roof support
and secure with (S1) screws with washers
19
. Place the ridge cover (RC1P) on top of Roof panel
and fix with Roof plug with washer and drive in Roof
Pins.
20
. Place the Roof panel (RP2AP) by sliding under
the Ridge cover (RC1P) to Roof support. Use (S1)
screws with washer to secure.
RP4AP
RC1P
RC1P
PPG
RC1P
RC1P
RP2AP
RC1P
RP2AP

Page 39
35
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
21
. Place the Ridge cover (RC2P) on top of Roof panel
and fix with Roof plugs with washer and drive in Roof
pins.
22
. Place the Roof panel (RP1AP) by sliding under
the Ridge cover (RC2P) to Roof support. Use (S1)
screw with washer to secure.
23
. Place the ridge cover (RC2P) on top of Roof panel
and fix with Roof plugs with washer and drive in roof
pins.
Fig.1
Fig.2
RC2P
PPG
PIN
RC2P
RP1AP
RC2P
RP1AP
RC2P
PPG
PIN

Page 40
36
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
24
. Insert the Roof flashing (RF1AP & RF2AP) under
the ridge cover. See fig. 1
Line up the holes and fix the roof plug with washer from
ridge cover through roof flashing to roof panel drive in
the roof pins. See fig. 2 & 3.
Use (S3) bolt & nut with washers to fix the Roof flashing
& Roof panel.
See fig. 4
Fig.2
Fig.4
25
. Fix the Roof flashing (RF3BP, RF4BP) at the edge
of roof panel with (S3) bolt & nut with washers at both
side, see the overlapping on the blow up.
26
. Place the Top corner (TC) on the Roof flashing
joint and secure with (S3) bolt & nut.
Fig.3
Fig.1
RF1AP
RF3BP
RF3BP
RF4BP
S3
TC
RF4BP
RF2AP
PIN
S3
RC2P
PPG
S3

Page 41
27
. Insert the Ridge end cap to the front & back top
of the roof and secure with (S1) screws with washer.
37
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
FC
S1

Page 42
38
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
D. Door
(1) Door panel
(DL1AP)
(1) Door panel
(DL2AP)
(1) Door panel
(DR1AP)
(1) Door panel
(DR2AP)
(2) Door panel strip top
(DSTAP)
(2) Door panel strip bottom
(DSBAP)
Parts Needed:
DSTAP
(2) Door panel middle support
(DMSAP)
(2) Door stopper vertical
(DSP)
(2) Door panel vertical support
(DVSP)
(2) Door handle
(DH)
(4) Bottom Slider
(BS)
(4) Sheet metal screw
(S1)
(38) Sheet metal screw
(S7)
(18) Machine screw
(S3)
(26) Plastic washer
(PW)
(26) Plastic screw cover
(PC)
DVSP
DL1AP
DMSAP
DL2AP
DR2AP
DR1AP
DMSAP
DVSP
DSTAP
DSBAP
DSP
DSBAP
DSP

Page 43
39
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
1
. Assemble the door panel (DR1AP & DR2AP) and
Door panel middle support (DMSAP) together with
(S3) bolt and nut from inside.
Right Door Assembly
DR2AP
DR1AP
DMSAP
S3
2
. Place the Door panel vertical support (DVSP) to the
Door panel (DR1AP) from inside. Secure the panel to
the (DVSP) Use (S7) screws with washer from outside.
DR2AP
DR1AP
Outside
inside
S7
DVSP
Outside
inside
DR2AP
DR1AP
DVSP
DMSAP
DR1AP

Page 44
40
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
3
. Assemble the Door stopper vertical (DSP) to the
Door panel (DR2AP) make sure the side edge of the
panel to be inserted into the door stopper profile (DSP).
Secure the stopper with Door panel with (S7) screw as
shown in fig.
DSP
DR2AP
S7
4
. Assemble the Door panel strip top (DSTAP) with
Door panel. Make sure the Door panel top edge to be
inserted into the (DSTAP). See fig. 1.
Secure the Door panel strip top (DSTAP) with door
stopper (DSP) with (S7) screw. See fig. 2.
Secure the Door panel with DSTAP use (S7) screws
with washer. See fig. 3.
Secure the DMSAP with DSTAP use (S7) screw.
See fig. 3
DSP
DSTAP
Fig.1
Fig.2
DSTAP
S7
Fig.3
Fig.4
S7
DSTAP
S7
DMSAP
DR2AP
DSP
1&2
3
4
DSTAP
DSP
S7
DVSP

Page 45
41
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
Fig.1
5
. Assemble the Door panel strip bottom (DSBAP) with
Door panel. Make sure the Door panel bottom edge to
be inserted into the (DSBAP). See fig. 1
Secure the strip (DSBAP) with Door stopper (DSP)
with (S7) screws. See fig. 2
Secure the Door panel with (DSTBP) use (S7)
screws with washer from outside. See fig. 3
Secure the (DMSAP) with (DSBAP) use (S7) screw.
See fig. 3.
Secure (DSBAP) with (DVSP) use (S7) screws.
See fig. 4
Fig.2
Fig.3
Fig.4
6
. Assemble to bottom slider (BS) to the Door panel.
Bottom side at both edge with (S3) bolt and nut with
washers.
BS
DMSAP
DSP
DMSAP
DSBAP
1&2
DSBAP
DVSP
DSBAP
DSBAP
DSP
S7
DSBAP
S7
3
4
S7
DVSP

Page 46
42
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
7
. Fix the Door handle (DH) with Door panel from front
side with bolt & nut.
Left Door Assembly
8
. Assemble the door panel (DL1AP & DL2AP) and
Door panel middle support (DMSAP) together with
(S3) bolt and nut from inside.
DMSAP
DL1AP
DMSAP
DL2AP
DL1AP
DL2AP
DMSAP
S3
DH

Page 47
43
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
9
. Place the door panel vertical support (DVSP) to
the Door panel (DL1AP) from inside secure the panel
to the (DVSP). Use (S7) screws with washer from
out side
.
DL1AP
DL1AP
DVSP
S7
10
. Assemble to Door stopper vertical (DSP) to the
Door panel (DL2AP). Make sure the side edge of
the panel to be inserted into the Door stopper profile
(DSP). Secure the stopper with Door panel with (S7)
screws as shown in fig.
DL2AP
DSP
S7
DVSP
DL1AP
DL2AP
DL1AP
DL2AP
DSP

Page 48
44
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
11
. Assemble the Door panel strip top (DSTAP)
with Door panel. Make sure the Door panel top edge
to be inserted into the (DSTAP).
Secure the Door panel strip top (DSTAP) with
Door stopper (DSP) with (S7) screws. See fig. 1&2.
Secure the Door panel with (DSTAP) use (S7)
screws with washers from out side. See fig. 3.
Secure the (DMSAP) with (DSTAP) use (S7)
screws from inside. See fig. 3
Secure the other end of (DSTAP) with (DVSP)
use (S7) screws. See fig. 4.
DSTAP
Fig.1
Fig.2
S7
Fig.3
Fig.4
S7
S7
12
. Assemble the Door Strip bottom (DSBAP) with
Door panel. Make sure the Door bottom edge to be
inserted into the (DSBAP).
Secure the Door panel strip bottom (DSBAP)
with Door stopper (DSP) with (S7) screws.
See fig. 1& 2.
Secure the Door panel with (DSBAP) use (S7)
screws with washers from out side. See fig. 3.
Secure the (DMSAP) with (DSBAP) use (S7)
screws from inside. See fig. 3
Secure the other end of (DSBAP) with (DVSP)
use (S7) screws. See fig. 4.
DSTAP
Fig.1
Fig.2
S7
Fig.3
Fig.4
S7
S7
DSTAP
DSBAP
DSBAP
DSP
DMSAP
DVSP
DSP
DSBAP
4
3
1&2
DVSP
DSTAP
DVSP
DSP
DMSAP
1&2
3
4

Page 49
45
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
13
. Assemble to bottom slider (BS) to the Door panel
bottom side at both edge with (S3) bolt and nut with
washers.
14
. Fix the Door handle (DH) with Door panel from
front side with bolt & nut.
S3
S3
BS
DH

Page 50
46
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
15
. Slide the Door panel assembly into the base bar
front (BBFP). Make sure the bottom slider (BS) should
slide inside the base bar front. See fig. 1.
Fix the Door panel top to the top slider (TS) with (S1)
screws. See fig. 2 & 3.
BS
BBFP
15 a
. To get proper alignment of the Door re-align the
holes with Door panel. See fig.
IMPORTANT
16
. Fix the plastic screw cover (PC) to the screws and
bolts edge from inside to prevent injury.
PC
PC
Fig.1
S1
TS
Fig.2
Fig.3
S1
TS
TS

Page 51
47
IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
17
. Cut the Edging Profile (EDP) to the required length
and insert to the Sliding Channel joint (SJP) to prevent
injury. See fig.
SJP
EDP
18
. Cut the Edging Profile (EDP) to the required length
and insert to the Facia Bracket Support (FBS) to prevent
injury. See fig.
EDP
1
1
1
1
2
2
Fig.1
Fig.2
FBS
EDP
FBS
19
. Cut the Edging Profile (EDP) to the required length
and insert to the Support Bracket (SB3AP & SB4AP)to
prevent injury. See fig.
EDP
SB3AP
SB4AP